Evaluation of the effects of slurry water immersion on the surface roughness of ADA type III and type IV dental stone casts
Journal Name:
- Süleyman Demirel Üniversitesi Sağlık Bilimleri Enstitüsü Dergisi
Keywords (Original Language):
Author Name | University of Author | Faculty of Author |
---|---|---|
Abstract (2. Language):
Objective: Surface properties of dental casts have critical
importance in dental laboratory procedures. However,
surface properties of the dental cast are affected by several
applications in dental laboratory. One of these applications
is the slurry water immersion of the dental casts in some
techniques such as preparing casts for duplication. Thus,
the aim of the present study was to compare the effects of
slurry water immersion and tap water immersion on the
surface roughness of type III and type IV dental stones.
Material-Method: Sixty master stone blocks were
prepared with type III and type IV dental stone. Half of
the each specimen group was immersed in slurry water
and the other half in tap water for 30 minutes. Each of four
groups was then allowed to dry for 24 hours without any
contamination to the surface of stone blocks. The surface
roughnesses of the specimens were determined using a
profilometer. The data were statistically analyzed using
one–way analysis of variance (ANOVA).
Results: Specimens immersed in tap water showed
statistically significant surface roughness (p<0.05) than
those immersed in slurry water. The difference was more
prominent between ADA type III dental stone groups.
Discussion: Slurry water dissolved the surface of gypsum
cast less than tap water. Thus, within the limitations of
the present study, it can be suggested that, to maintain
the surface accuracy of the dental casts, slurry water
immersion should be preferred instead of tap water
immersion.
Bookmark/Search this post with
Abstract (Original Language):
Amaç: Alçı ile hazırlanan dental modellerin yüzey
özellikleri, dental laboratuarda gerçekleştilen işlemler
üzerinde önemli etkiye sahiptir. Bunun yanında
dental modellerin yüzey özellikleri farklı uygulamalar
sonucunda değişebilmektedir. Bu uygulamalardan birisi,
dental modellerin çoğaltılması işleminde olduğu gibi,
modellerin suda bekletilmesidir. Bu çalışmanın amacı,
alçılı suda ve musluk suyunda bekletilen ADA tip III ve
tip IV dental alçı ile hazırlanmış dental modellerin yüzey
pürüzlülüğünün karşılaştırılmasıdır.
Materyal–Metot: ADA tip III ve tip IV dental alçı
kullanılarak 60 adet örnek hazırlandı. Her bir örnek
grubunun yarısı alçı ile doygunluğa ulaşmış suda ve diğer
yarısı musluk suyunda 30 dakika bekletildi. Sonrasında,
örnekler yüzey kontaminasyonu olmayacak şekilde 24
saat kurumaya bırakıldı. Örneklerin yüzey pürüzlülükleri
profilometre cihazı kullanılarak değerlendirildi. Verilerin
analizi tek yönlü varyans analizi (ANOVA) kullanılarak
değerlendirildi.
Bulgular: ADA tip III ve tip IV dental alçı ile hazırlanarak
musluk suyunda ve alçılı suda bekletilen örneklerin yüzey
pürüzlülüğü değerlerinin karşılaştırılması istatistiksel olarak
anlamlı bulundu (p<0.05). Bu farklılık ADA tip III dental
alçı ile hazırlanan örneklerde daha fazla olarak bulgulandı.
Tartışma: ADA tip III ve tip IV dental alçı ile hazırlanmış
modellerin alçılı suda bekletilmesi, yüzey pürüzlülüğünü
daha az etkilemektedir. Bu çalışmanın sınırları dahilinde,
alçı modellerin yüzey özelliklerinin korunması için,
modellerin musluk suyu yerine alçılı suda bekletilmesi
önerilebilir.
FULL TEXT (PDF):
- 3
103-107